MAFci Prototype needed in Baltimore Washington Area

www.cp-e.com · #1 (**permalink**) 10-03-2005, 06:10 PM

Hello,

We have developed a MAFci System for the 2002-2004 3.5 Altima with big hp gains at the wheels. THE 2002-2003 WIRING AND FUEL MAPS HAVE BEEN VERIFIED, and are now available. With 1.5 hours of installation time, the Mazda6s MAFci System™ offers average gains of 16.58 hp and 15.85 ft lbs., with peak differences of 24.03 hp and 20.35 ft lbs. The 2002-2003 Nissan Altima offers average gains of 15.32 hp and 15.59 ft lbs., with peak differences of 26.13 hp and 23.56 ft lbs. Please e-mail me at JAdams@cp-e.com for dyno graphs of the Altima, web page has not been updated yet. It is average horsepower that is important and is the factor that will bring quarter mile times down.

A MAFci System is our, Custom Performance Engineering, Inc., line of intake systems. It is the first line of intelligent intakes designed specifically for mass air sensor equipped cars and trucks. The Nissan mass air flow sensor makes the Altima SE-R a perfect candidate for the MAFci System.

Every MAFci System includes a high flow aFe reusable filter and all the associated plumbing (Usually 3.5" OD pipe), a bigger mass air sensor housing, associated hardware, and a MAF Customizer. The MAF Customizer is what allows the use of bigger mass air housing and is also used to tune the car for gains not possible with other intakes.

This post is to find a Nissan Altima SE-R to map the fuel trims. The hardware is the same in the 2002-2005's. We do not expect money we just want a list to determine if there is interest out there. If there is interest then we will develop and test a prototype to determine if the gains are there. If they are we would like to sell it if not the project will be scrapped.

We are also looking for a stock performing 2004 Altima in the Washington DC, Baltimore area to do the development on. In return the owner will receive a free tunable intake for use on his/her Altima.

We would also like your input. What types of things would you like to see included in the design of this intake.

Please visit www.mazda6tech.com, www.mazda6club.com to see voiced opinions of our products. Please also check out the dyno video of the STi MAFci System on our web page, www.cp-e.com. Please direct all e-mails, questions to Josh Adams at Jadams@cp-e.com. Thank you again for your time.

Very Respectfully,

Custom Performance Engineering

6802 Mid Cities Ave.
Beltsville MD 20705

301 576 6142
www.cp-e.com
__________________
www.cp-e.com
Custom Performance Engineering, Inc.

"Performance with Style"

virgilio7 · #2 (**permalink**) 10-03-2005, 07:56 PM

ser owners this is your oportunity for a powerfull modification. don't complain later saying there are no mods.
this is one that you WILL need.

virgilio7 · #3 (**permalink**) 10-14-2005, 04:58 AM

just to show my emotion toward the product. WHAT A CHANGE. tomorrow night I'll problably get some videos and share with you guys.
this is a must have.

virgilio7 · #4 (**permalink**) 10-14-2005, 04:59 AM

just to show my emotion toward the product. WHAT A CHANGE. tomorrow night I'll problably get some videos and share with you guys.
this is a must have.

altimateone · #5 (**permalink**) 10-14-2005, 05:08 AM

those numbers on the Alti are on a completely stock 3.5 right. Virg your going to get the dyno with headers...

Velicos · #6 (**permalink**) 10-14-2005, 06:44 AM

Virg did you get the tunable version?

The CPe just doesn't make sense to me as there is the S-AFCII and the Berk V2...

virgilio7 · #7 (**permalink**) 10-14-2005, 12:57 PM

well I thought the same. When I saw the real program. is a nice program. much much more tunable than the safc2. as soon as I installed I felt a big difference at wot. that is me and my firend butt dyno of course. today I'm going to do a couple of passes on a dyno to check a/f ratio but eventually this software is very complete. I will love to send you some information but until cp-e approves the copy of the documents they send, I can't do it. they install was a piece of cake. I did it in an hour and a half. this software can be integrated later to a wideband sensor (they are going to release a baddass one). another thing is 2 different maps at a flip of a switch. I'll ask them to see if I can take some snapshots of the software to show you guys.

Velicos · #8 (**permalink**) 10-14-2005, 03:42 PM

Well hmph, I'll have to talk with you one evening and go over a thing or two to see if it's really worth getting. There hasn't been any real proof or data on the boards besides DJ's few images he posted.

wild willy · #9 (**permalink**) 10-14-2005, 05:12 PM

I will have interest in this product for my 02...

virgilio7 · #10 (**permalink**) 10-14-2005, 07:29 PM

how about tomorrow at moroso if it doesn't rain? half way for both of us lol.

Andrios · #11 (**permalink**) 10-28-2005, 08:43 AM

Any updates??I might sell my injen and my S-afc2(lol just got it) and get the CPE.....is it worth it?

Velicos · #12 (**permalink**) 10-28-2005, 02:21 PM

^^ Hold onto the Injen / S-AFCII.....lol

Unless they actually come out with real results that are amazing it's not worth the investment.

Andrios · #13 (**permalink**) 10-29-2005, 01:06 PM

Yeah but Im very impatient

I hope someone has numbers soon, cant wait to atleast tune my car.

Da Mayor · #14 (**permalink**) 10-29-2005, 04:01 PM

i spoke with josh there very nice guy at cp-e so i might take a drive down there so he can do some R&D on my altima.

AltimaPimpin · #15 (**permalink**) 11-07-2005, 11:51 PM

Will these work with the Technosquare ECU?

Will it yield even bigger gains? Or will the two just cancel out?
I don't know if I should wait for the cp-e to come out first before I get the Technosquare, or if it doesn't even matter.

Thanks in advance, and very sorry for the thread-jack.

Pete